How to Fix Error Code 0x80300024, When Installing Windows

We’ll talk about how to patch windows 10 0x80300024, windows can’t mount this drive, windows can’t install error 0x80300001, and windows 10 install error code 0x80300024 throughout this article. When installing some variation of the system’s operating system, multiple errors occur during the installation process.

Among the many potential mistakes, 0x80300024 is one of them. The error code 0x80300024 is followed by an error message that reads, in part, “Windows is unable to install to the selected location.”

Solved: Error Code 0x80300024 After Installing Windows

You will learn how to repair error code 0x80300024 in this article.

Here are the specifics:

This error code 0x80300024 indicates a problem with a software application or equipment associated with the hard drive partition where the Windows installation is located. This error code 0x80300024 can also be caused by several factors ranging from a lack of disk space on the location drive to defective/corrupted installation media to a damaged, dying, or otherwise damaged disk drive.

Here are a few ways to solving their respective problems. To arrive at the predicted results, follow the steps.

Solution #1: Get rid of any hard drives that aren’t needed.

If the machine has more than one hard disk drive connected to it and Windows is installed on one of them, the other drives could interfere with the installation, resulting in the structure failing and the error code 0x80300024 the device. To make sure this isn’t the case, delete all hard disk drives that aren’t being used for Windows installation from the computer/laptop, and then retry the facility to see if the issue persists.

If this method fails to remove the error code 0x80300024, there is no problem with the disk drives, and you can proceed to the next step, which addresses a few other possible causes for this error.

Solution #2: Make the installation location look good.

If the partition on the hard disk used to install Windows has been used before and is not a newly created partition, any of the details on it may interfere with the Windows setup. This is why, before installing Windows on a computer system, it is still a good idea to plan out the installation area.

If the data in the installation position is the cause of the issue, it is recommended that the configuration location be fully formatted, which would effectively fix the error code 0x80300024.

Follow the instructions below to do so:

Step 1: Reboot the device after inserting the bootable Windows configuration media. If the Windows installation media isn’t available to use, you’ll have to make your own.

Step 2: As the computer machine starts up, choose the placed setup media to boot.

Step 3: Configure the computer’s language, keyboard layout, and other preferences.

Step 4: Choose the Customized solution when asked about the kind of Windows installation you want.

Step 5: When prompted for the position of the Windows to be installed in, select Drive options first (innovative).

Step 6: To find the partition of the computer’s disk drive where Windows will be loaded, press it, and click Format.

Step 7: Double-check the operation.

Step 8: Wait for the drive partitioning to be correctly formatted before clicking Next to continue with the installation.

Solution #3: Use a different USB port to connect the installation media.

If you’re trying to load Windows from a USB drive with the correct setup media on it, as most people do, the problem may be the USB port into which the setup media is plugged.

If this is the cause of the error code, consider loading Windows with the USB drive containing the installation media in a different USB port– switch from a USB 2.0 port to a USB 3.0 port or the other way around to see if Windows can be successfully installed. If the USB does not cause the error code 0x80300024, proceed to the following procedure.

Solution #4:Verify that the Target Drive is mentioned first in the computer’s boot order.

The hard disk may also trigger this error code 0x80300024. It is configured to start at the bottom of the computer’s boot order. A machine has a resource order when it first starts up. It wants to boot from the operating system, and this order is set up in the BIOS of a regular machine.

All that is needed to resolve the 0x80300024 problem is to keep an eye on it. The goal hard drive is placed first in the boot order of the computer device. To do so, follow the steps outlined below for much better results:

Step 1: Switch on the screen.

Step 2: During the increase up, on the very first screen that appears on the monitor. There are instructions for pressing a certain key, which is usually Erase. To access the BIOS/Setup of the machine, press F1/F2. To enter the BIOS, press the designated key.

Step 3: Locate the computer system’s boot order/configuration in the BIOS. In most instances, the boot order can be found under the Boot tab of the BIOS.

Step 4: Ensure that the boot order is changed. The hard disk that Windows will be mounted on is at the very front.

Step 5: Exit the BIOGRAPHIES of the computer system. However, before you do so, be careful to save any modifications that have been upgraded.

Once you’ve completed all of these measures, reboot your Windows installation and see if everything went smoothly.

Solution #5: Get a new hard drive

If none of the strategies mentioned above are effective in resolving the error code 0x80300024 problem. It’s possible that the operating system’s hard disk drive is failing or has already died. A resisting drive would certainly prevent the installation of a Windows operating system. If everything fails, replace the operating system’s hard disk drive with a new one. When completed, the error code 0x80300024 issue will be resolved.


The 0x80300024 error has a high probability of causing problems. As a result, it’s usually best to identify the problem first and then apply the solutions. A step-by-step approach is often recommended for improved and more precise results.

Related Articles

Stay Connected


Latest Articles